Mazuzil Do not overwork the Chapdur Premix and do not spray water to wet out surfaces treated with Chapdur Premix. Dispose of in accordance with local regulations. Flush immediately with water for 10 — 15 minutes and contact a physician immediately. Chapdur Premix is a ready to use blend of graded hard aggregates of mineral origin, pigments and Portland Cement. Users should always refer to the most recent issue of the Technical Data Sheet for the product concerned, copies of which will be supplied on request, or can be accessed on the internet under www.
|Published (Last):||9 December 2013|
|PDF File Size:||5.69 Mb|
|ePub File Size:||8.6 Mb|
|Price:||Free* [*Free Regsitration Required]|
Mazuzil Do not overwork the Chapdur Premix and do not spray water to wet out surfaces treated with Chapdur Premix.
Dispose of in accordance with local regulations. Flush immediately with water for 10 — 15 minutes and contact a physician immediately. Chapdur Premix is a ready to use blend of graded hard aggregates of mineral origin, pigments and Portland Cement. Users should always refer to the most recent issue of the Technical Data Sheet for the product concerned, copies of which will be supplied on request, or can be accessed on the internet under www.
Chqpdur common rule-ofthumb practice is when light foot traffic leaves a 3 — 5mm imprint. Once the base concrete slab is levelled, sprinkle Chapdur Premix along the edges and compact into the surface using a steel trowel.
In practice, the differences in materials, substrates and actual site conditions are such that no warranty in respect of merchantability or cahpdur fitness for a particular purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or from any written recommendations, or from any other advice offered.
Remove affected person to fresh air immediately and contact a physician. The Company reserves itself the right to change the formulation of Sika products if so required by new research and development. The base concrete shall be laid and compacted in accordance with good concrete practice with particular attention to bay edges and premiix.
Use of safety goggles and chemical resistant gloves are recommended. Wash clothing before re-use. Once the Chapdur Premix has been evenly moistened by the concrete water, compact the floor with a low speed mechanical trowel.
Warehouses Engineering workshops Car parks, garages, service stations Quays Factories. Premiz Chapdur Premix surface must be protected to prevent rapid water loss which may result in surface cracks. Wash hands immediately after use. All orders are accepted subject to our current terms of sale and delivery which are available on request.
Chapdur Premix contains Portland Cement, Silica, and other graded aggregates. Remove uncured Chapdur Premix from tools and equipment with water immediately after use.
Care should be taken to ensure that the slab is laid accurately to finish profile and that excess water and laitance build up is kept to a minimum. As surface areas at edges and adjacent joints are subjected to heavier impact and wear, additional treatment should be considered for these areas.
Remove contaminated clothing immediately. Contact Sika for further health and safety information. Cured material can only be removed mechanically. When Chapdur Premix is applied too early, water needed for hydration of the concrete will be absorbed and this may affect the strength of the concrete surface layer. The proprietary rights of third parties must be observed. Apply 0,6kg per lineal metre over a width of mm. Collect with suitable absorbent material.
Timing for application is crucial. Chapdur Premix is used as a dry shake, nonmetallic surface hardener for new concrete floor slabs and screeds where good abrasion resistance and reduced dusting is required, such as in: Related Posts
Sika Chapdur Premix
The concrete should Contain an adequate proportion of cement. It is recommended to add a suitable Sika concrete admixture to improve its properties e. Level the freshly poured concrete by means of a vibrating beam. As soon as the plasticity permits, smooth the concrete preferably by using a mechanical trowel. The concrete slab is ready for the Chapdurs cement coating when a thumb pressed hard onto the surface only leaves a print of about 3 - 5 mm depth.
Sika Chapdur Non Metallic Floor Hardener
CHAPDUR PREMIX PDF